Automobile diesel fuel (EN 590) Grade E (winter), recommended for use at ambient temperatures up to minus 15 C (limiting filterability temperature).
Diesel fuel EN 590 (EN 590) Grade E is obtained from petroleum refined products and is intended for use as automotive fuel for diesel engines of cars and trucks. Diesel fuel meets the requirements of the international standard EN 590/2000 and is characterized by a low content of sulfur, aromatic hydrocarbons and a high cetane number, which leads to an overall reduction in sulfur oxide emissions, a decrease in the amount of particulate matter in exhaust gases and the formation of deposits in the fuel system of cars and heavy vehicles, reducing exhaust smoke and is the key to good starting properties of the fuel during cold start of the engine.
The oil refining industry produces diesel fuel in accordance with GOST 305-82 of three grades:
L - summer, used at ambient temperatures above 0 C;
3 - winter, used at temperatures up to -20 C (in this case, winter diesel fuel should have a stagnation <-35 C and n <-25 C), or winter, used at temperatures up to -30 C, then the fuel must have a stasis <-45 C and n <-35 C);
- Arctic diesel fuel, the temperature of which is up to -50 C. The sulfur content in diesel fuel of grades L and Z does not exceed 0.2% for type I fuel and 0.5 for type II fuel, and grade A 0.4%
We have the below available products ready for supply.
Contact us for immidate transaction
1) D2- Gas Oil (Diesel) Lo.2-62 Gost 305-82 , Quantity- 50,000mt - 500,000mt For Cif And Fob, Spot And Contract Basis.
2) Jp54 Aviation Kerosine Colonial Grade 54 Russia Origin, Quantity- 1,000,000bbls 8,000,000bbls For Cif And Fob, Spot And Contract Basis.
3) Aviation Turbine Fuel Jet A-1 Quantity- 1,000,000bbls 8,000,000bbls For Cif And Fob, Spot And Contract Basis.
4) Bitumen Quantity - 50,000mt - 500,000mt, Cif And Fob, Spot And Contract Basis.
5) M100 Mazut 100 Gost 10585-99 And 10585-75, Quantity- 50,000mt 500,000mt, Cif And Fob, Spot And Contract Basis.
6) Liquid Petroleum Gas.Gost 20448-90, Quantity 50,000mt- 500,000mt, Cif And Fob, Spot And Contract Basis.
7) Liquified Natural Gas, Quantity 50,000mt 500,000mt, For Cif And Fob, Spot And Contract Basis.
8) Russia Sn 150 Base Oil, Quantity - 5,000mt - 50,000mt, For Cif And Fob, Spot And Contract Basis.
9) Russia Sn 500 Base Oil, Quantity - 5,000mt - 50,000mt, For Cif And Fob, Spot And Contract Basis.
10) En590 Biodiesel, Quantity 50,000mt- 500,000mt, For Cif And Fob, Spot And Contract Basis.
11) Automotive Gas And Oil (Ago), Quantity 50,000mt - 500,000mt, For Cif And Fob, Spot And Contract Basis.
PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions.
Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency.
As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process.
The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather.
Our products are exported to Asia, Europe, America, and the CIS.
PETROALLIANCE diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions.
Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency.
As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process.
The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather.
Our products are exported to Asia, Europe, America, and the CIS.
1. Buyer issues Irrevocable Corporate Purchase Order (ICPO) with client information sheet (CIS) and Bank
Comfort Letter (BCL).
2. Seller issues Draft Sales and Purchase Agreement (SPA) and, Commercial Invoice for Buyer's review
and signing.
3. Buyer signs the Sales and Purchase Agreement and Commercial Invoice back to the Seller. Seller has
authorization to verify (ATV) Buyer bank for BCL.
4. Seller's Lawyer legalizes the signed Sales and Purchase Agreement.
5. Seller sends legalized Sales and Purchase Agreement and below Partial POP Documents as listed
below to Buyer:
a. Certificate of Origin
b. Commitment to Supply
c. Product Passport
d. Statement of Availability of the product
e. Export license
6. Buyer issues their Financial Guarantee (SBLC/MT760) to cover the first (month) shipment to the Seller's
bank within 3-5 working Days.
7. If Buyer fails to issue SBLC/MT760 in 3-5 working days, in alternative Buyer shall make Security
Guarantee Deposit of 2% via T. T Wire of total value of the first shipment to Seller's fiduciary bank account
as performance to secure the allocation, which will be deducted from the first shipment.
8. Upon confirmation of Buyer's SBLC/MT760 or Security Guarantee Deposit of 2% via T. T Wire to Seller's
fiduciary bank, Seller will issue 2% Performance Bond, Full POP and Shipping Documents via SWIFT
bank-to-bank as shown below:
a. Product Allocation Export Permit
b. Allocation Title Ownership Certificate
c. Contract to transport the product to the loading port
d. Port storage agreement
e. Charter party Agreement to transport the product to discharge port
f. Tank Storage Receipt
g. SGS Quality and Quantity Certificate
h. Bill of Loading
i. Vessel Questionnaire 88
Note: Products of non-sanctioned countries, vessels & documents are non-Russian.
9. Shipment commences and upon arrival of the vessel tanker at the discharge port, Buyer conducts SGS
or Equivalence Inspection for Quantity & Quality and makes payment for the full shipment via TT Wire
or MT103 within 72 hours.
Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions.
Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency.
As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process.
The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather.
Our products are exported to Asia, Europe, America, and the CIS
product Description : These Products are Exported with Stringent Adherence to Standard Russian Export Specifications with Respective GOST. Price of product ( USD price or FOB price) : Product will be priced in USD$ Based on an Appropriate PLATTS INDEX or a FIXED Price and the Agreed Upon Shipping Method. The Price will be Mutually Agreed to by Buyer and Seller Product origin : Russian Federation Key Specifications/Delivery/Logistics : 1. Certification SGC or Equivalent 2. Payment Terms = Letter of Credit ( Details to be agreed upon by Buyer and Seller 3. Delivery Time = Varies by Destination 4. Port of Loading = TBD Minimum Order Size & Contract Term : Minimum Monthly Quantity = 100,000 MT X 12 Month Contract Required with R & E up to 120 Months
D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators.
D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names.
Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400
Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil.
The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol.
D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.
Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions.
Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency.
As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process.
The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather.
Our products are exported to Asia, Europe, America, and the CIS
Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions.
Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency.
As a result of their inherently higher compression ratio for a given power output, diesel engines are more fuel efficient than spark ignition engines. Compared with spark ignition automotive engines, diesel engines weigh more, generate more vibration and produce greater particulate or soot emissions. Diesel engines can also produce a particularly carcinogenic type of hydrocarbon pollutant known as polycyclic aromatic hydrocarbons (PAHs), which are generated during the diesel combustion process.
The cetane index is a measure of the autoignition quality of a diesel fuel, with higher numbers meaning that the engine is easier to start in cold weather.
Our products are exported to Asia, Europe, America, and the CIS
Diesel fuel is generally a liquid fuel used in diesel engines, which ignites the fuel without sparking by compressing the inlet air mixture and then injecting the fuel. (Glow plugs, grid heaters, and block heaters help achieve high combustion temperatures during cold weather starting.)
The most common type of diesel fuel is specific fractional distillation of fuel oil, but alternatives that are not derived from oil, such as biodiesel, biomass to liquid (BTL) or gas to liquid (GTL) diesel, are increasingly being developed and adopted.
To distinguish these types, in some academic circles, petroleum-derived diesel fuel is increasingly referred to as oil-oil. Ultra Low Sulfur Diesel (ULSD) is the standard for determining substantially reduced sulfur diesel.
Light Cycle Oil (LCO) is a diesel boiling range product from Fluid Catalytic Cracking Units (FCCUs). FCCU is responsible for the production of petrol, LPG and Light Cycle Oil (LCO).
There are various ways of economically upgrading LCO, which include hydrotreating, high pressure hydrocracking for full conversion of LCO into Naphtha and a more optimized partial conversion hydrocracking process.
It can be used in susch industries as Agrochemical, Crude Oil, Petrochemicals, Petroleum Products.
Diesel fuel is generally a liquid fuel used in diesel engines, which ignites the fuel without sparking by compressing the inlet air mixture and then injecting the fuel. (Glow plugs, grid heaters, and block heaters help achieve high combustion temperatures during cold weather starting.)
The most common type of diesel fuel is specific fractional distillation of fuel oil, but alternatives that are not derived from oil, such as biodiesel, biomass to liquid (BTL) or gas to liquid (GTL) diesel, are increasingly being developed and adopted.
To distinguish these types, in some academic circles, petroleum-derived diesel fuel is increasingly referred to as oil-oil. Ultra Low Sulfur Diesel (ULSD) is the standard for determining substantially reduced sulfur diesel.
Mazut-100 is a fuel oil that is manufactured to GOST specifications, for example GOST 10585-75/99.
GOST is the Russian system of standards. Mazut is almost exclusively manufactured in the Russian Federation, This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock.
For shipment purposes, this product has a high viscosity which drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil.
The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels:
- "Very Low Sulphur" is mazut with a sulphur content of 0.5%
- "Low Sulphur" is a mazut with a sulphur content of 0.5-1.0%
- "Normal Sulphur" is a mazut with a sulphur content of 1.0-2.0%
- "High Sulphur" is a mazut with a sulphur content of 2.0-3.5%
- Very Low Sulfur mazut is generally made from the lowest sulfur crude feedstocks.
The dealer company is looking for a distributor of an oil refinery to enter into an annual Contract for the purchase of diesel fuel EN 590 10 ppm, of Qatar or Saudi Arabia origin in the amount of 30,000 MT per month. Total quantity: 360 000 MT per year; Terms of delivery: CIF seaport Tallinn (Estonia), Klaipda (Lithuania); Terms of payment: DLC (MT700); Price: 380 $ tons; Product quality: European Union EN 590 standard; Inspection: SGS/ Equivalent; Delivery time: shipment of the first batch within 10 days after issuing the letter of credit. Contact person: Nick
The dealer company is looking for Buyers for diesel fuel EN 590 10 ppm produced in Azerbaijan in volumes from 5,000 to 15,000 metric tons per month on EXW terms, Klaipeda Sea port terminal (Lithuania), according to Incoterms 2020. Total quantity: 5,000 - 180,000 MT per year. The first batch is trial, with a possible extension of the Agreement for 11 months; Payment terms: DLC (MT700), irrevocable, divisible, transferable; Price: $670 - $680 per ton; Product quality: European Union standard EN 590; Inspection: SGS/equivalent; Performance guarantee: 2% of the nominal value of the monthly delivery by the Seller's Bank to the Buyer's Bank; Delivery term: within 20 working days from the date of issue of the letter of credit by the Buyer. Contact person: Nik
The dealer company is looking for Buyers for the conclusion of annual Contracts for the sale of EN 590 10 ppm diesel fuel produced in countries that are not under sanctions, in volumes from 25,000 to 100,000 tons per month, FOB Rotterdam. Delivery of the first batch of goods in the amount of 25,000 - 50,000 MT is trial; Total quantity: 300,000 - 1,200,000 tons per year; Terms of payment: MT103/TT; Price: $ 625 - 630 MT; Product quality: European Union standard EN 590; Inspection: SGS/equivalent; Transaction procedure DIP & PAY: The Buyer issues ICPO together with TSA, and the Seller, in turn, provides the Buyer with PPOP (ATV, TSR, Injection Report and DTA). Contact person: Nick
The dealer company is looking for Buyers to enter into annual Contracts for the sale of EN 590 10 ppm diesel fuel produced in non-sanctioned countries, in volumes from 50,000 to 100,000 tons per month, FOB Fujairah. The delivery of the first batch of goods in the amount of 50,000 - 50,000 MT is trial; Total quantity: 600,000 - 1,200,000 tons per year; Terms of payment: MT103/TT; Price: $ 690 MT; Product quality: European Union standard EN 590; Inspection: SGS/equivalent; Transaction procedure DIP & PAY: The Buyer issues the ICPO and after receiving the CI, provides the BCL, in response, the Seller provides the Buyer with the PPOP (Fresh report of SGS, ATV, TSR, Injection Report and DTA). Contact person: Nick
148 Diesel En590 Suppliers
Short on time? Let Diesel En590 sellers contact you.
